国产精品国产自产 I 96亚洲精品久久久蜜桃 I 涩视频在线 I 翔田千里精品久久一区二 I 337p日本欧洲亚洲大胆 I 字幕日韩视频一区二区 I 日韩偷拍一区二区 I 免费一级大片 I 九九久久精品国产av片国产 I 午夜福利92国语 I 国产免费97 I 波多野结衣福利视频 I 男人和女人在羞羞视频 I 久久精彩视频 I 忘忧草社区中文字幕www I 日韩影视一区二区三区 I 青青av I 国产av熟女一区二区三区 I 亚洲日韩片无码中文字幕 I 懂色av一区二区三区四区 I 国产伦人人人人人人性 I 91亚洲黄色 I 人妻丰满熟妇av无码区免 I 中文字幕人成人乱码亚洲电影 I 大伊人久久 I 免费人成在线观看网站品爱网 I 黄色三级免费片 I 我看午夜视频 I 性欧美色图 I 日韩三级一区二区

5. Lack of glue in rubber products Reason analysis: 1. The rubber material does not flow sufficiently; 2. The unit consumption of semi-finished products is insufficient or the amount of glue loaded is insufficient; 3.3. Poor mold exhaust performance; mold temperature is too high Solution: 1. Slow down the rising speed of the mold and repeatedly deflate; 2. Re-establish the amount of glue in the mold; 3.3. Improve mold design and reduce mold temperature. 6. Rolling, drawing and shrinking of rubber products Reason analysis: 1 The air between the mold and the rubber cannot be discharged. 2 The weighing is not enough. 3 Insufficient pressure. 4 The fluidity of the rubber compound is too poor. 5. The mold temperature is too high, and the rubber material is scorched. 6.6 Early scorch of the compound (dead material). 7. The material is not thick enough and the flow is not sufficient. Solution: 1. Add a vent slot. 2. Multi-exhaust. 3. Raise stress 4. Modify the formula to increase the fluidity of the rubber compound. 5. Modify the formula to prolong the scorch time 6. Increase the thickness of the material. 7. Cracks appear in rubber products Analysis of the reasons: Dirt is mixed in the rubber compound; too much release agent is added; the rubber compound is not scorched enough. Solution: Ensure that the rubber compound is clean and pollution-free; use the release agent reasonably; prolong the scorch time. 8. Rubber products are frosted and whitish Reason analysis: 1. Insufficient vulcanization. 2. Excessive compounding agent exceeds the solubility of rubber. Solution: 1. Extend sulfur or take secondary vulcanization 2. Adjust formula to reduce low solubility 9. Rubber product demoulding and cracking Reasons: 1. The mold temperature is too high or the sulfur time is too long. 2. Too much vulcanizing agent. 3. The demoulding method is incorrect. Solutions: 1. Reduce the mold temperature. 2. Shorten the sulfur time. 3. Reduce the amount of vulcanizing agent. 4. Spray release agent. 5. Take the correct demoulding method. 10. Rubber products are difficult to process Reason analysis: 1. The tear strength of the product is too good (such as high tensile glue). This difficult processing is manifested in that the burrs cannot be torn off. 2. The strength of the product is too poor, which means that the burrs are very brittle and will tear together with the product. Remedy: 1. If it cannot be torn off, the formula must be adjusted, and the compounding agent should be filled more to reduce the shrinkage rate. 2. If it is torn, reduce the mold temperature, when shortening the sulfur, reduce the amount of vulcanizing agent, adjust the formula, and increase the strength of the rubber compound